Fire And Water Damage Restoration in Melbourne, FL
The fire was in the kitchen, but the water from the hoses is now in the basement, the subfloor and every wall cavity on the first floor. One call connects you with an independent, licensed and insured fire and water restoration contractor in Melbourne that can extract, dry and clean in the right order.
- Water extraction & structural drying
- Moisture mapping
- Soot & smoke cleanup
- Licensed & insured independent pros
Why Fire and Water Damage Need One Plan in Melbourne
Almost every fire loss is also a water loss. A fire hose can move well over a hundred gallons a minute, sprinklers discharge, and heat can burst supply lines. That water carries dissolved soot into subfloors, wall cavities and insulation, so you are drying contaminated water, not clean water.
The order of operations matters. Extraction and drying usually come first because mold can start on wet materials in 24 to 48 hours. Yet air movers can spread soot, so crews contain the area, HEPA-vacuum first and run scrubbers alongside the drying gear.
Drying is driven by psychrometrics, the relationship between air temperature, humidity and moisture. Crews map moisture with meters and thermal imaging, set air movers and low-grain refrigerant dehumidifiers, and log readings daily until materials hit dry standard.
Re Fire Me is a free referral service, not the contractor. We route Melbourne calls to independent, licensed and insured contractors experienced in both, many trained to IICRC S500 and S700.
Where firefighting water hides
- Under hardwood, laminate and tile
- Inside wall cavities and insulation
- In ceiling drywall below upper floors
- Basements and crawlspaces
- Behind cabinets and baseboards
Why Choose Our Specialized Fire And Water Damage Restoration in Melbourne, FL
You need a contractor fluent in both fire and water work. Here is what the independent contractors we connect you with in Melbourne bring.
Licensed & insured contractors
Calls go to independent, licensed and insured businesses that do both water mitigation and fire restoration.
Upfront written pricing
You get a written scope covering extraction, drying days, equipment, soot cleaning and repairs before major work starts.
Rapid local dispatch
Drying has to start fast, and crews near Melbourne can often begin extraction within hours.
Drying & detection equipment
Truck-mount extractors, LGR dehumidifiers, air movers, wall-cavity drying systems, moisture meters, thermal cameras and HEPA scrubbers.
Combined Fire and Water Solutions Around Melbourne
These are the core steps on a combined fire and water loss.
Water Extraction
Pumps and truck-mount extractors pull standing water from floors, carpet and pad. Faster extraction means shorter drying times.
Moisture Mapping
Moisture meters and thermal imaging trace water into walls, under floors and into ceilings below. That map decides equipment placement and what has to come out.
Structural Drying
Equipment placement follows psychrometric readings, and wall cavities are dried in place when possible. Readings are logged daily.
Soot Cleanup in Wet Areas
Loose soot is HEPA-vacuumed before air movers run, and residue carried by water is cleaned from floors and lower walls.
Mold Prevention
Fast drying, removal of materials that will not dry in time and antimicrobial application help prevent mold.
Repairs After Drying
Once materials reach dry standard, removed drywall, flooring and insulation are replaced and finishes restored.
Understanding the Water Left Behind After a Fire
Restoration pros sort water losses into categories by contamination. Category 1 is clean water from a supply line, Category 2 has some contamination, and Category 3 is grossly contaminated water such as sewage or floodwater.
Firefighting water often starts clean but picks up soot, ash, chemicals and debris as it moves through the building. Depending on what it touched and how long it sat, it may be treated as Category 2 or even Category 3, which affects what materials can be dried in place and what has to be removed.
That is exactly why combined losses need a contractor fluent in both. Carpet pad soaked with sooty water is usually removed. Drywall wicking dirty water above a certain height may be cut out. Hard surfaces get cleaned and treated before drying finishes.
Drying logs are one of the most useful documents on a fire and water job. Each day, technicians record moisture readings at marked points, along with temperature and humidity inside and outside the drying area. Those numbers show whether drying is progressing and when materials reach dry standard. Adjusters rely on them to approve equipment charges, and you can rely on them to know the structure is actually dry before walls are closed up and finishes go back on.
Fire and Water Situations We Hear About Most
Upstairs fire, downstairs water
The fire is on the second floor, but the hose water comes through the ceilings below. The first floor needs moisture mapping, drying and ceiling repairs even though it never saw a flame.
Sprinkler discharge in a business
A small fire triggers sprinkler heads in an office or warehouse. The fire is minor, but water spreads across carpet, inventory and lower walls, and drying has to start immediately to reopen quickly.
Pipes burst by heat
Heat from a fire can melt or burst supply lines inside walls, so water keeps flowing after the fire is out. Shutting off the water, finding the break and drying the cavity become urgent.
Crawlspace and basement flooding
Water collects in crawlspaces and basements where it is out of sight. Extraction, dehumidification and moisture monitoring there prevent mold and wood rot under the house.
Hardwood floors soaked by hoses
Hardwood floors that took on firefighting water can cup and buckle. Specialized floor drying mats and dehumidifiers can sometimes save them if drying starts quickly, while waiting usually means replacement.
The 4-Step Fire and Water Process
Call Dispatch
Call +1-866-484-1409 and describe where the water is and where the fire started. We connect you with an independent contractor near Melbourne.
Rapid Mobile Arrival
On arrival, the crew extracts water and sets up containment and HEPA scrubbers.
Expert Assessment & Quote
After mapping moisture and soot, the lead provides a written scope with drying time and repairs.
Resolution & Final Walkthrough
Drying, cleaning and repairs are completed in order, with moisture logs and a final walkthrough.
Fire and Water Stories From Melbourne
The fire was upstairs, but the water came through the ceilings on the first floor. Their thermal camera found water in walls I would never have thought to check.
Ellen W.Homeowner, Melbourne
A small office fire set off our warehouse sprinklers. They dried the concrete and racks, cleaned the soot and had us operating again in a week.
Frank Z.Business owner, Melbourne
We got daily moisture readings, and the adjuster accepted the drying logs as submitted. No mold, no smell.
Angela and Ray T.Homeowners, Melbourne
They explained why the carpet could be saved but the pad had to go. The drying took four days and the house smells normal again.
Josh M.Homeowner, Melbourne
Common Fire and Water Questions in Melbourne
Why is there so much water damage after a fire?
Hoses, sprinklers and heat-burst pipes all add water. That water soaks into floors, walls and ceilings far from where the fire burned.
Should drying or soot cleaning happen first?
Drying generally starts first because mold can develop within a day or two. Crews HEPA-vacuum loose soot and run air scrubbers so the drying equipment does not spread residue.
How long does it take to dry a home after a fire?
With the right equipment, most buildings dry in three to five days. Dense materials like hardwood and concrete can take longer.
Can firefighting water cause mold?
It can. Mold may start on wet drywall, wood and insulation within a day or two. Fast extraction and professional drying are the best prevention.
Is Re Fire Me the restoration contractor?
No. Re Fire Me is a free referral service connecting you with independent, licensed and insured contractors. The contractor performs and is responsible for the work.
Does insurance cover water damage from putting out a fire?
Generally, yes. Water used to extinguish a covered fire is typically part of the fire claim. Review your policy and keep the drying records.
Fire and Water Coverage in Melbourne and Nearby
We take calls from Melbourne and nearby areas around the clock. Contractors work on houses, condos, apartments and sprinklered commercial buildings. See nearby cities and zip codes below.
Contractors around Melbourne handle combined fire and water losses in homes with basements, slab foundations and crawlspaces.
Water Will Not Wait. Neither Should You.
Wet materials can start growing mold within a day or two. Call +1-866-484-1409 to connect with an independent fire and water contractor in Melbourne.
